Satt 19 inch rack I/O, a rack-based I/O system, can be connected to AC 800M using the CI865 interface module. CI865 supports online replacement (Hot Swap), and does not require any configuration before installation. The CI865 unit handles I/O scanning of up to 31 distributed...Read More
The AC 800M controller supports up to four CI862 CEX modules and 1,000 TRIO/Genius I/O points. TRIO supports CEX module redundancy. The CI862 unit also handles the I/O configuration and I/O scanning of up to 30 TRIO blocks.
Brand: ABB
Place of origin:...Read More
The CI860 can be used in redundant mode, up to twelve CI860 modules can be placed at one AC800 M also in redundant mode, and each of them can be connected to the same or to a separate FOUNDATION Field bus HSE subnet. The ABB FOUNDATION Field bus Linking Device LD800HSE/LD...Read More
Drive Bus supports Hot Swap. A maximum of 24 ABB drives can be connected to one CI858 and a maximum of two CI858 can be connected to an AC 800M controller. If more than one ABB drive is connected to the CI858, a branching unit NDBU is needed, which enables the construction of...Read More
Maximum number of MCUs (or other INSUM devices) per AC 800M: – 256 MCUs (or other INSUM devices) per AC 800M with PM864 or PM866. – 128 MCUs (or other INSUM devices) per AC 800M with PM861; maximum 6 CI857 per AC 800M; maximum 128 MCUs (or other INSUM devices) per CI857;...Read More
A key benefit with the CI856 interface is the possibility to reuse the majority of the existing I/O installation, including terminations and field wiring in existing ABB Master and Advant OCS installations. Single connection to S100 I/O units located in up to five I/O racks...Read More
The ABB CI855 has MB 300 network redundancy; clock synchronization; dataset communication; hot swap and per to peer communication.
Brand: ABB
Place of origin: Sweden
Delivery: 8 to 10 weeksRead More
The ABB CI854A is used for connecting remote I/O and field bus instruments via PROFIBUS D and possible to connect PROFIBUS PA to the CI854B via the PROFIBUS linking device LD 800P. The CI854B can be set redundant
Brand: ABB
Place of origin: Sweden
...Read More
The ABB CI854A is used for connecting remote I/O and field bus instruments via PROFIBUS DP and possible to connect PROFIBUS PA to the CI854A/ CI854B via the PROFIBUS linking device LD 800P. The CI854A and newer CI854B can be set redundant
Brand: ABB
Place of...Read More
The ABB CI853 COMLI can be used on the build in COM3 port and optionally on the CI853 ports. RS-232C is the standard communication interface used for serial communication with COMLI. The CI853 supports Hot Swap. COMLI is an ABB protocol for data transmission between...Read More
The ABB DP820 has 8 channels and the modules can be used in both single and redundant applications, interface for NAMUR, 12 V and 24 V transducer signal levels, each channel can be configured for pulse count or frequency measurement. The inputs can also be read as DI signals...Read More
The ABB DP820 has two channels, interface for RS422, 5 V, 12 V, 24 V and 13 mA transducer signal levels and simultaneous pulse count and frequency measurement, pulse count (length/position) by accumulation in a bidirectional 29 bit counter, frequency (speed) measurement 0.25...Read More
We are professional 800x suppliers and contractors in Dubai of UAE, involved in engineering, programming and installation service. Our factory provides high quality integrator products for Yokogawa and ABB. We also supply wide range of revamping, upgrading, commissioning, immigration and configuration spare parts service. Be free to buy 800x at good price here and get quotation from us.