1. General introduction
Nano Coriolis mass flow meter is for low flow applications, typical line sizes: DN15, DN25, DN40, 1/4”, 3/8”,1/2”, 1”, 1 1/2” and maximum mass flow up to 1.5 t/h, the dual tube design compensates for fluctuations of density, temperature, pressure and environment conditions, this provides a consistent repeatable and accurate measurement especially for small size Coriolis flow meters. Two type of transmitters selectable as Essential type with basic function and Ultimate type with high function.
2. Measuring range limits
Meter size | Normal Mass Flow | Maximum mass flow | Normal Volume flow | Max Volume flow | Normal Temperature | Max. Temperature | Density |
Nano 06 | 0.021 t/h | 0.04 t/h | 0.021m3/h | 0.04 m3/h | -50 to150℃ | -50 to 260℃ | 0 to 5 kg/l |
Nano 08 | 0.045 t/h | 0.094 t/h | 0.045 m3/h | 0.094 m3/h | |||
Nano 10 | 0.17 t/h | 0.3 t/h | 0.17 m3/h | 0.3 m3/h | |||
Nano 15 | 0.37 t/h | 0.6 t/h | 0.37 m3/h | 0.6 m3/h | |||
Nano 20 | 0.95 t/h | 1.5 t/h | 0.95 m3/h | 1.5 m3/h |
3. Accuracy of liquids measurement
Measured quantity | Accuracy for transmitters | ||
Essential | Ultimate | ||
Mass flow | Accuracy | 0.2 % of measured value | 0.1 % of measured value |
Repeatability | 0.1 % of measured value | 0.05 % of measured value | |
Volume flow | Accuracy | 0.45 % of measured value | 0.12 % of measured value |
Repeatability | 0.23 % of measured value | 0.06 % of measured value | |
Density | Accuracy | 4 g/l (0.25 lb/ft³) | 0.5 g/l (0.03 lb/ft³) |
Repeatability | 2 g/l (0.13 lb/ft³) | 0.3 g/l (0.02 lb/ft³) | |
Temperature | Accuracy | 0.5℃ (0.9℉) | 0.5℃ (0.9℉) |
4. Accuracy of gas measurement
Measured quantity | Accuracy for transmitters | ||
Essential | Ultimate | ||
Mass flow | Accuracy | 0.75 % of measured value | 0.5 % of measured value |
Repeatability | 0.6 % of measured value | 0.4 % of measured value | |
Volume flow | Accuracy | 0.75 % of measured value | 0.5 % of measured value |
Repeatability | 0.6 % of measured value | 0.4 % of measured value | |
Temperature | Accuracy | 0.5℃ (0.9℉) | 0.5℃ (0.9℉) |
5. Model selection of Nano 06
Main Code | Suffix Codes | Description | |||||||||||||
RC | Always RC | ||||||||||||||
Transmitter | E | Essential (base function) | |||||||||||||
U | Ultimate (high function) | ||||||||||||||
Sensor | N | Nano | |||||||||||||
Meter size | 06 | Nominal mass flow : 0.021 t/h (0.77 lb/min), Maximum mass flow: 0.04 t/h (1.5 lb/min) | |||||||||||||
Material of wetted parts | K | Measuring tubes: Ni alloy C-22/2.4602, Process connections: stainless steel 1.4404/316L | |||||||||||||
Process connection size | 06 | ¼" | |||||||||||||
08 | ⅜" | ||||||||||||||
15 | DN15, ½" | ||||||||||||||
20 | ¾" | ||||||||||||||
Process connection type | BA1 | ASME flange class 150, suitable for ASME B16.5, raised face (RF) | |||||||||||||
BA2 | ASME flange class 300, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
BA4 | ASME flange class 600, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA4 | ASME flange class 600, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BA5 | ASME flange class 900, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA5 | ASME flange class 900, suitable for ASME B16.5, ring joint( RJ) | ||||||||||||||
BA6 | ASME flange class 1500, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA6 | ASME flange class 1500, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BD4 | EN flange PN 40, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED4 | EN flange PN 40, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD4 | EN flange PN 40, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD4 | EN flange PN 40, suitable for EN 1092-1 type D, groove | ||||||||||||||
BD6 | EN flange PN 100, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED6 | EN flange PN 100, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD6 | EN flange PN 100, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD6 | EN flange PN 100, suitable for EN 1092-1 type D, groove | ||||||||||||||
BJ1 | JIS flange 10K, JIS B 2220 | ||||||||||||||
BJ2 | JIS flange 20K, JIS B 2220 | ||||||||||||||
BP1 | JPI flange class 150 | ||||||||||||||
BP2 | JPI flange class 300 | ||||||||||||||
BP4 | JPI flange class 600 | ||||||||||||||
HS4 | Clamp process connection according to DIN 32676 series A | ||||||||||||||
HS8 | Clamp process connection according to DIN 32676 series C(Tri-Clamp) | ||||||||||||||
TG9 | Process connection with internal thread G | ||||||||||||||
TT9 | Process connection with internal thread NPT | ||||||||||||||
Sensor housing 0material | 0 | Stainless steel 1.4301/304, 1.4404/316L | |||||||||||||
1 | Stainless steel 1.4404/316L | ||||||||||||||
Process fluid temperature range | 0 | Standard: -50 to 150℃ (-58 to 302℉) | |||||||||||||
2 | Mid-range: -50 to 260℃ (-58 to 500℉) | ||||||||||||||
Mass flow and density accuracy | E9 | Liquid: 0.2 % maximum mass flow deviation, 20 g/l density deviation | |||||||||||||
D9 | Liquid: 0.15 % maximum mass flow deviation, 20 g/l density deviation | ||||||||||||||
70 | Gas: 0.75% maximum mass flow deviation | ||||||||||||||
50 | Gas: 0.5% maximum mass flow deviation | ||||||||||||||
Design and housing | A | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and standard neck sensor | |||||||||||||
B | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
E | Remote type with "corrosion protection coating" coated aluminum transmitter housing and standard neck sensor | ||||||||||||||
F | Remote type with "corrosion protection coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
J | Remote type stainless steel transmitter and standard neck sensor | ||||||||||||||
K | Remote type stainless steel transmitter and long neck sensor | ||||||||||||||
Ex approval | NN00 | None | |||||||||||||
KF21 | ATEX, explosion group IIC and IIIC | ||||||||||||||
KF22 | ATEX, explosion group IIB and IIIC | ||||||||||||||
SF21 | IECEx, explosion group IIC and IIIC | ||||||||||||||
SF22 | IECEx, explosion group IIB and IIIC | ||||||||||||||
GF21 | EAC Ex, explosion group IIC and IIIC | ||||||||||||||
GF22 | EAC Ex, explosion group IIB and IIIC | ||||||||||||||
FF11 | FM, groups A, B, C, D, E, F, G | ||||||||||||||
FF12 | FM, groups C, D, E, F, G | ||||||||||||||
UF21 | INMETRO, explosion group IIC and IIIC | ||||||||||||||
UF22 | INMETRO, explosion group IIB and IIIC | ||||||||||||||
NF21 | NEPSI, explosion group IIC and IIIC | ||||||||||||||
NF22 | NEPSI, explosion group IIB and IIIC | ||||||||||||||
PF21 | Korea Ex, explosion group IIC and IIIC | ||||||||||||||
PF22 | Korea Ex, explosion group IIB and IIIC | ||||||||||||||
Cable entries | 2 | ANSI ½" NPT | |||||||||||||
4 | ISO M20x1.5 | ||||||||||||||
Communication type and I/O | JA | active current output HART,1 passive pulse or status output | |||||||||||||
JB | 2 active current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JC | 2 active current outputs one with HART,1 passive pulse or status output,1 voltage-free status input | ||||||||||||||
JD | 1 active current output HART,2 passive pulse or status outputs,1 passive status output | ||||||||||||||
JE | 1 active current output HART,2 passive pulse or status outputs,1 voltage-free status input | ||||||||||||||
JF | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output with pull-up resistor,1 voltage-free status input | ||||||||||||||
JG | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output,1 voltage-free status input | ||||||||||||||
JH | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 active current input | ||||||||||||||
JJ | 1 active current output HART,2 passive pulse or status outputs,1 active current input | ||||||||||||||
JK | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 active current input | ||||||||||||||
JL | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 passive current input | ||||||||||||||
JM | 1 active current output HART,2 passive pulse or status outputs,1 passive current input | ||||||||||||||
JN | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 passive current input | ||||||||||||||
JP | 2 passive current outputs one with HART,1 passive pulse or status output | ||||||||||||||
JQ | 2 passive current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JR | 2 passive current outputs one with HART,1 passive NAMUR pulse or status output | ||||||||||||||
JS | 2 passive current outputs one with HART,2 passive NAMUR pulse or status outputs | ||||||||||||||
M0 | Modbus output,1 passive pulse or status output | ||||||||||||||
M2 | Modbus output,1 passive pulse or status output,1 active current input | ||||||||||||||
M3 | Modbus output, 2 passive pulse or status outputs | ||||||||||||||
M4 | Modbus output,1 passive pulse or status output, 1 active pulse or status output | ||||||||||||||
M5 | Modbus output, 1 passive pulse or status output, 1 active pulse or status output with pull-up resistor | ||||||||||||||
M6 | Modbus output,1 passive pulse or status output, 1 active current output | ||||||||||||||
M7 | Modbus output, 1 passive pulse or status output, 1 passive current input | ||||||||||||||
Display | 0 | No display | |||||||||||||
1 | With display | ||||||||||||||
Optional codes | /Optional codes |
6. Model selection of Nano 08
Main Code | Suffix Codes | Description | |||||||||||||
RC | Always RC | ||||||||||||||
Transmitter | E | Essential (base function) | |||||||||||||
U | Ultimate (high function) | ||||||||||||||
Sensor | N | Nano | |||||||||||||
Meter size | 08 | Nominal mass flow : 0.045 t/h (1.7 lb/min), Maximum mass flow: 0.094 t/h (3.5 lb/min) | |||||||||||||
Material of wetted parts | K | Measuring tubes: Ni alloy C-22/2.4602, Process connections: stainless steel 1.4404/316L | |||||||||||||
Process connection size | 06 | ¼" | |||||||||||||
08 | ⅜" | ||||||||||||||
15 | DN15, ½" | ||||||||||||||
20 | ¾" | ||||||||||||||
25 | DN25, 1" | ||||||||||||||
40 | DN40, 1½" | ||||||||||||||
Process connection type | BA1 | ASME flange class 150, suitable for ASME B16.5, raised face (RF) | |||||||||||||
BA2 | ASME flange class 300, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
BA4 | ASME flange class 600, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA4 | ASME flange class 600, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BA5 | ASME flange class 900, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA5 | ASME flange class 900, suitable for ASME B16.5, ring joint( RJ) | ||||||||||||||
BA6 | ASME flange class 1500, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA6 | ASME flange class 1500, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BD4 | EN flange PN 40, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED4 | EN flange PN 40, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD4 | EN flange PN 40, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD4 | EN flange PN 40, suitable for EN 1092-1 type D, groove | ||||||||||||||
BD6 | EN flange PN 100, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED6 | EN flange PN 100, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD6 | EN flange PN 100, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD6 | EN flange PN 100, suitable for EN 1092-1 type D, groove | ||||||||||||||
BJ1 | JIS flange 10K, JIS B 2220 | ||||||||||||||
BJ2 | JIS flange 20K, JIS B 2220 | ||||||||||||||
BP1 | JPI flange class 150 | ||||||||||||||
BP2 | JPI flange class 300 | ||||||||||||||
BP4 | JPI flange class 600 | ||||||||||||||
HS4 | Clamp process connection according to DIN 32676 series A | ||||||||||||||
HS8 | Clamp process connection according to DIN 32676 series C(Tri-Clamp) | ||||||||||||||
TG9 | Process connection with internal thread G | ||||||||||||||
TT9 | Process connection with internal thread NPT | ||||||||||||||
Sensor housing 0material | 0 | Stainless steel 1.4301/304, 1.4404/316L | |||||||||||||
1 | Stainless steel 1.4404/316L | ||||||||||||||
Process fluid temperature range | 0 | Standard: -50 to 150℃ (-58 to 302℉) | |||||||||||||
2 | Mid-range: -50 to 260℃ (-58 to 500℉) | ||||||||||||||
Mass flow and density accuracy | E8 | Liquid: 0.2 % maximum mass flow deviation, 8 g/l density deviation | |||||||||||||
D8 | Liquid: 0.15 % maximum mass flow deviation, 8 g/l density deviation | ||||||||||||||
C8 | Liquid: 0.1 % maximum mass flow deviation, 8 g/l density deviation | ||||||||||||||
70 | Gas: 0.75% maximum mass flow deviation | ||||||||||||||
50 | Gas: 0.5% maximum mass flow deviation | ||||||||||||||
Design and housing | A | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and standard neck sensor | |||||||||||||
B | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
E | Remote type with "corrosion protection coating" coated aluminum transmitter housing and standard neck sensor | ||||||||||||||
F | Remote type with "corrosion protection coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
J | Remote type stainless steel transmitter and standard neck sensor | ||||||||||||||
K | Remote type stainless steel transmitter and long neck sensor | ||||||||||||||
Ex approval | NN00 | None | |||||||||||||
KF21 | ATEX, explosion group IIC and IIIC | ||||||||||||||
KF22 | ATEX, explosion group IIB and IIIC | ||||||||||||||
SF21 | IECEx, explosion group IIC and IIIC | ||||||||||||||
SF22 | IECEx, explosion group IIB and IIIC | ||||||||||||||
GF21 | EAC Ex, explosion group IIC and IIIC | ||||||||||||||
GF22 | EAC Ex, explosion group IIB and IIIC | ||||||||||||||
FF11 | FM, groups A, B, C, D, E, F, G | ||||||||||||||
FF12 | FM, groups C, D, E, F, G | ||||||||||||||
UF21 | INMETRO, explosion group IIC and IIIC | ||||||||||||||
UF22 | INMETRO, explosion group IIB and IIIC | ||||||||||||||
NF21 | NEPSI, explosion group IIC and IIIC | ||||||||||||||
NF22 | NEPSI, explosion group IIB and IIIC | ||||||||||||||
PF21 | Korea Ex, explosion group IIC and IIIC | ||||||||||||||
PF22 | Korea Ex, explosion group IIB and IIIC | ||||||||||||||
Cable entries | 2 | ANSI ½" NPT | |||||||||||||
4 | ISO M20x1.5 | ||||||||||||||
Communication type and I/O | JA | active current output HART,1 passive pulse or status output | |||||||||||||
JB | 2 active current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JC | 2 active current outputs one with HART,1 passive pulse or status output,1 voltage-free status input | ||||||||||||||
JD | 1 active current output HART,2 passive pulse or status outputs,1 passive status output | ||||||||||||||
JE | 1 active current output HART,2 passive pulse or status outputs,1 voltage-free status input | ||||||||||||||
JF | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output with pull-up resistor,1 voltage-free status input | ||||||||||||||
JG | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output,1 voltage-free status input | ||||||||||||||
JH | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 active current input | ||||||||||||||
JJ | 1 active current output HART,2 passive pulse or status outputs,1 active current input | ||||||||||||||
JK | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 active current input | ||||||||||||||
JL | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 passive current input | ||||||||||||||
JM | 1 active current output HART, 2 passive pulse or status outputs,1 passive current input | ||||||||||||||
JN | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 passive current input | ||||||||||||||
JP | 2 passive current outputs one with HART,1 passive pulse or status output | ||||||||||||||
JQ | 2 passive current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JR | 2 passive current outputs one with HART,1 passive NAMUR pulse or status output | ||||||||||||||
JS | 2 passive current outputs one with HART,2 passive NAMUR pulse or status outputs | ||||||||||||||
M0 | Modbus output,1 passive pulse or status output | ||||||||||||||
M2 | Modbus output,1 passive pulse or status output,1 active current input | ||||||||||||||
M3 | Modbus output, 2 passive pulse or status outputs | ||||||||||||||
M4 | Modbus output,1 passive pulse or status output, 1 active pulse or status output | ||||||||||||||
M5 | Modbus output, 1 passive pulse or status output, 1 active pulse or status output with pull-up resistor | ||||||||||||||
M6 | Modbus output,1 passive pulse or status output, 1 active current output | ||||||||||||||
M7 | Modbus output, 1 passive pulse or status output, 1 passive current input | ||||||||||||||
Display | 0 | No display | |||||||||||||
1 | With display | ||||||||||||||
Optional codes | /Optional codes |
7. Model selection of Nano 10
Main Code | Suffix Codes | Description | |||||||||||||
RC | Always RC | ||||||||||||||
Transmitter | E | Essential (base function) | |||||||||||||
U | Ultimate (high function) | ||||||||||||||
Sensor | N | Nano | |||||||||||||
Meter size | 10 | Nominal mass flow : 0.17 t/h (6.2 lb/min), Maximum mass flow: 0.3 t/h (11 lb/min) | |||||||||||||
Material of wetted parts | K | Measuring tubes: Ni alloy C-22/2.4602, Process connections: stainless steel 1.4404/316L | |||||||||||||
Process connection size | 06 | ¼" | |||||||||||||
08 | ⅜" | ||||||||||||||
15 | DN15, ½" | ||||||||||||||
20 | ¾" | ||||||||||||||
25 | DN25, 1" | ||||||||||||||
40 | DN40, 1½" | ||||||||||||||
Process connection type | BA1 | ASME flange class 150, suitable for ASME B16.5, raised face (RF) | |||||||||||||
BA2 | ASME flange class 300, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
BA4 | ASME flange class 600, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA4 | ASME flange class 600, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BA5 | ASME flange class 900, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA5 | ASME flange class 900, suitable for ASME B16.5, ring joint( RJ) | ||||||||||||||
BA6 | ASME flange class 1500, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA6 | ASME flange class 1500, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BD4 | EN flange PN 40, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED4 | EN flange PN 40, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD4 | EN flange PN 40, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD4 | EN flange PN 40, suitable for EN 1092-1 type D, groove | ||||||||||||||
BD6 | EN flange PN 100, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED6 | EN flange PN 100, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD6 | EN flange PN 100, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD6 | EN flange PN 100, suitable for EN 1092-1 type D, groove | ||||||||||||||
BJ1 | JIS flange 10K, JIS B 2220 | ||||||||||||||
BJ2 | JIS flange 20K, JIS B 2220 | ||||||||||||||
BP1 | JPI flange class 150 | ||||||||||||||
BP2 | JPI flange class 300 | ||||||||||||||
BP4 | JPI flange class 600 | ||||||||||||||
HS4 | Clamp process connection according to DIN 32676 series A | ||||||||||||||
HS8 | Clamp process connection according to DIN 32676 series C(Tri-Clamp) | ||||||||||||||
TG9 | Process connection with internal thread G | ||||||||||||||
TT9 | Process connection with internal thread NPT | ||||||||||||||
Sensor housing 0material | 0 | Stainless steel 1.4301/304, 1.4404/316L | |||||||||||||
1 | Stainless steel 1.4404/316L | ||||||||||||||
Process fluid temperature range | 0 | Standard: -50 to 150℃ (-58 to 302℉) | |||||||||||||
2 | Mid-range: -50 to 260℃ (-58 to 500℉) | ||||||||||||||
Mass flow and density accuracy | E7 | Liquid: 0.2 % maximum mass flow deviation, 4 g/l density deviation | |||||||||||||
D7 | Liquid: 0.15 % maximum mass flow deviation, 4 g/l density deviation | ||||||||||||||
D3 | Liquid: 0.15 % maximum mass flow deviation, 1 g/l density deviation | ||||||||||||||
C7 | Liquid: 0.1 % maximum mass flow deviation, 4 g/l density deviation | ||||||||||||||
C3 | Liquid: 0.1 % maximum mass flow deviation, 1 g/l density deviation | ||||||||||||||
70 | Gas: 0.75% maximum mass flow deviation | ||||||||||||||
50 | Gas: 0.5% maximum mass flow deviation | ||||||||||||||
Design and housing | A | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and standard neck sensor | |||||||||||||
B | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
E | Remote type with "corrosion protection coating" coated aluminum transmitter housing and standard neck sensor | ||||||||||||||
F | Remote type with "corrosion protection coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
J | Remote type stainless steel transmitter and standard neck sensor | ||||||||||||||
K | Remote type stainless steel transmitter and long neck sensor | ||||||||||||||
Ex approval | NN00 | None | |||||||||||||
KF21 | ATEX, explosion group IIC and IIIC | ||||||||||||||
KF22 | ATEX, explosion group IIB and IIIC | ||||||||||||||
SF21 | IECEx, explosion group IIC and IIIC | ||||||||||||||
SF22 | IECEx, explosion group IIB and IIIC | ||||||||||||||
GF21 | EAC Ex, explosion group IIC and IIIC | ||||||||||||||
GF22 | EAC Ex, explosion group IIB and IIIC | ||||||||||||||
FF11 | FM, groups A, B, C, D, E, F, G | ||||||||||||||
FF12 | FM, groups C, D, E, F, G | ||||||||||||||
UF21 | INMETRO, explosion group IIC and IIIC | ||||||||||||||
UF22 | INMETRO, explosion group IIB and IIIC | ||||||||||||||
NF21 | NEPSI, explosion group IIC and IIIC | ||||||||||||||
NF22 | NEPSI, explosion group IIB and IIIC | ||||||||||||||
PF21 | Korea Ex, explosion group IIC and IIIC | ||||||||||||||
PF22 | Korea Ex, explosion group IIB and IIIC | ||||||||||||||
Cable entries | 2 | ANSI ½" NPT | |||||||||||||
4 | ISO M20x1.5 | ||||||||||||||
Communication type and I/O | JA | active current output HART,1 passive pulse or status output | |||||||||||||
JB | 2 active current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JC | 2 active current outputs one with HART,1 passive pulse or status output,1 voltage-free status input | ||||||||||||||
JD | 1 active current output HART,2 passive pulse or status outputs,1 passive status output | ||||||||||||||
JE | 1 active current output HART,2 passive pulse or status outputs,1 voltage-free status input | ||||||||||||||
JF | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output with pull-up resistor,1 voltage-free status input | ||||||||||||||
JG | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output,1 voltage-free status input | ||||||||||||||
JH | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 active current input | ||||||||||||||
JJ | 1 active current output HART,2 passive pulse or status outputs,1 active current input | ||||||||||||||
JK | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 active current input | ||||||||||||||
JL | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 passive current input | ||||||||||||||
JM | 1 active current output HART, 2 passive pulse or status outputs,1 passive current input | ||||||||||||||
JN | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 passive current input | ||||||||||||||
JP | 2 passive current outputs one with HART,1 passive pulse or status output | ||||||||||||||
JQ | 2 passive current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JR | 2 passive current outputs one with HART,1 passive NAMUR pulse or status output | ||||||||||||||
JS | 2 passive current outputs one with HART,2 passive NAMUR pulse or status outputs | ||||||||||||||
M0 | Modbus output,1 passive pulse or status output | ||||||||||||||
M2 | Modbus output,1 passive pulse or status output,1 active current input | ||||||||||||||
M3 | Modbus output, 2 passive pulse or status outputs | ||||||||||||||
M4 | Modbus output,1 passive pulse or status output, 1 active pulse or status output | ||||||||||||||
M5 | Modbus output, 1 passive pulse or status output, 1 active pulse or status output with pull-up resistor | ||||||||||||||
M6 | Modbus output,1 passive pulse or status output, 1 active current output | ||||||||||||||
M7 | Modbus output, 1 passive pulse or status output, 1 passive current input | ||||||||||||||
Display | 0 | No display | |||||||||||||
1 | With display | ||||||||||||||
Optional codes | /Optional codes |
8. Model selection of Nano 15
Main Code | Suffix Codes | Description | |||||||||||||
RC | Always RC | ||||||||||||||
Transmitter | E | Essential (base function) | |||||||||||||
U | Ultimate (high function) | ||||||||||||||
Sensor | N | Nano | |||||||||||||
Meter size | 15 | Nominal mass flow : 0.37 t/h (14 lb/min), Maximum mass flow: 0.6 t/h (22 lb/min) | |||||||||||||
Material of wetted parts | K | Measuring tubes: Ni alloy C-22/2.4602, Process connections: stainless steel 1.4404/316L | |||||||||||||
Process connection size | 06 | ¼" | |||||||||||||
08 | ⅜" | ||||||||||||||
15 | DN15, ½" | ||||||||||||||
20 | ¾" | ||||||||||||||
25 | DN25, 1" | ||||||||||||||
40 | DN40, 1½" | ||||||||||||||
Process connection type | BA1 | ASME flange class 150, suitable for ASME B16.5, raised face (RF) | |||||||||||||
BA2 | ASME flange class 300, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
BA4 | ASME flange class 600, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA4 | ASME flange class 600, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BA5 | ASME flange class 900, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA5 | ASME flange class 900, suitable for ASME B16.5, ring joint( RJ) | ||||||||||||||
BA6 | ASME flange class 1500, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA6 | ASME flange class 1500, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BD4 | EN flange PN 40, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED4 | EN flange PN 40, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD4 | EN flange PN 40, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD4 | EN flange PN 40, suitable for EN 1092-1 type D, groove | ||||||||||||||
BD6 | EN flange PN 100, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED6 | EN flange PN 100, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD6 | EN flange PN 100, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD6 | EN flange PN 100, suitable for EN 1092-1 type D, groove | ||||||||||||||
BJ1 | JIS flange 10K, JIS B 2220 | ||||||||||||||
BJ2 | JIS flange 20K, JIS B 2220 | ||||||||||||||
BP1 | JPI flange class 150 | ||||||||||||||
BP2 | JPI flange class 300 | ||||||||||||||
BP4 | JPI flange class 600 | ||||||||||||||
HS4 | Clamp process connection according to DIN 32676 series A | ||||||||||||||
HS8 | Clamp process connection according to DIN 32676 series C(Tri-Clamp) | ||||||||||||||
TG9 | Process connection with internal thread G | ||||||||||||||
TT9 | Process connection with internal thread NPT | ||||||||||||||
Sensor housing 0material | 0 | Stainless steel 1.4301/304, 1.4404/316L | |||||||||||||
1 | Stainless steel 1.4404/316L | ||||||||||||||
Process fluid temperature range | 0 | Standard: -50 to 150℃ (-58 to 302℉) | |||||||||||||
2 | Mid-range: -50 to 260℃ (-58 to 500℉) | ||||||||||||||
Mass flow and density accuracy | E7 | Liquid: 0.2 % maximum mass flow deviation, 4 g/l density deviation | |||||||||||||
D7 | Liquid: 0.15 % maximum mass flow deviation, 4 g/l density deviation | ||||||||||||||
D3 | Liquid: 0.15 % maximum mass flow deviation, 1 g/l density deviation | ||||||||||||||
C7 | Liquid: 0.1 % maximum mass flow deviation, 4 g/l density deviation | ||||||||||||||
D2 | Liquid: 0.15 % maximum mass flow deviation, 0.5 g/l density deviation | ||||||||||||||
C3 | Liquid: 0.1 % maximum mass flow deviation, 1 g/l density deviation | ||||||||||||||
C2 | Liquid: 0.1 % maximum mass flow deviation, 0.5 g/l density deviation | ||||||||||||||
70 | Gas: 0.75% maximum mass flow deviation | ||||||||||||||
50 | Gas: 0.5% maximum mass flow deviation | ||||||||||||||
Design and housing | A | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and standard neck sensor | |||||||||||||
B | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
E | Remote type with "corrosion protection coating" coated aluminum transmitter housing and standard neck sensor | ||||||||||||||
F | Remote type with "corrosion protection coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
J | Remote type stainless steel transmitter and standard neck sensor | ||||||||||||||
K | Remote type stainless steel transmitter and long neck sensor | ||||||||||||||
Ex approval | NN00 | None | |||||||||||||
KF21 | ATEX, explosion group IIC and IIIC | ||||||||||||||
KF22 | ATEX, explosion group IIB and IIIC | ||||||||||||||
SF21 | IECEx, explosion group IIC and IIIC | ||||||||||||||
SF22 | IECEx, explosion group IIB and IIIC | ||||||||||||||
GF21 | EAC Ex, explosion group IIC and IIIC | ||||||||||||||
GF22 | EAC Ex, explosion group IIB and IIIC | ||||||||||||||
FF11 | FM, groups A, B, C, D, E, F, G | ||||||||||||||
FF12 | FM, groups C, D, E, F, G | ||||||||||||||
UF21 | INMETRO, explosion group IIC and IIIC | ||||||||||||||
UF22 | INMETRO, explosion group IIB and IIIC | ||||||||||||||
NF21 | NEPSI, explosion group IIC and IIIC | ||||||||||||||
NF22 | NEPSI, explosion group IIB and IIIC | ||||||||||||||
PF21 | Korea Ex, explosion group IIC and IIIC | ||||||||||||||
PF22 | Korea Ex, explosion group IIB and IIIC | ||||||||||||||
Cable entries | 2 | ANSI ½" NPT | |||||||||||||
4 | ISO M20x1.5 | ||||||||||||||
Communication type and I/O | JA | active current output HART,1 passive pulse or status output | |||||||||||||
JB | 2 active current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JC | 2 active current outputs one with HART,1 passive pulse or status output,1 voltage-free status input | ||||||||||||||
JD | 1 active current output HART,2 passive pulse or status outputs,1 passive status output | ||||||||||||||
JE | 1 active current output HART,2 passive pulse or status outputs,1 voltage-free status input | ||||||||||||||
JF | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output with pull-up resistor,1 voltage-free status input | ||||||||||||||
JG | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output,1 voltage-free status input | ||||||||||||||
JH | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 active current input | ||||||||||||||
JJ | 1 active current output HART,2 passive pulse or status outputs,1 active current input | ||||||||||||||
JK | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 active current input | ||||||||||||||
JL | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 passive current input | ||||||||||||||
JM | 1 active current output HART, 2 passive pulse or status outputs,1 passive current input | ||||||||||||||
JN | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 passive current input | ||||||||||||||
JP | 2 passive current outputs one with HART,1 passive pulse or status output | ||||||||||||||
JQ | 2 passive current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JR | 2 passive current outputs one with HART,1 passive NAMUR pulse or status output | ||||||||||||||
JS | 2 passive current outputs one with HART,2 passive NAMUR pulse or status outputs | ||||||||||||||
M0 | Modbus output,1 passive pulse or status output | ||||||||||||||
M2 | Modbus output,1 passive pulse or status output,1 active current input | ||||||||||||||
M3 | Modbus output, 2 passive pulse or status outputs | ||||||||||||||
M4 | Modbus output,1 passive pulse or status output, 1 active pulse or status output | ||||||||||||||
M5 | Modbus output, 1 passive pulse or status output, 1 active pulse or status output with pull-up resistor | ||||||||||||||
M6 | Modbus output,1 passive pulse or status output, 1 active current output | ||||||||||||||
M7 | Modbus output, 1 passive pulse or status output, 1 passive current input | ||||||||||||||
Display | 0 | No display | |||||||||||||
1 | With display | ||||||||||||||
Optional codes | /Optional codes |
9. Model selection of Nano 20
Main Code | Suffix Codes | Description | |||||||||||||
RC | Always RC | ||||||||||||||
Transmitter | E | Essential (base function) | |||||||||||||
U | Ultimate (high function) | ||||||||||||||
Sensor | N | Nano | |||||||||||||
Meter size | 20 | Nominal mass flow : 0.95 t/h (35 lb/min), Maximum mass flow: 1.5 t/h (55 lb/min) | |||||||||||||
Material of wetted parts | K | Measuring tubes: Ni alloy C-22/2.4602, Process connections: stainless steel 1.4404/316L | |||||||||||||
Process connection size | 06 | ¼" | |||||||||||||
08 | ⅜" | ||||||||||||||
15 | DN15, ½" | ||||||||||||||
20 | ¾" | ||||||||||||||
25 | DN25, 1" | ||||||||||||||
40 | DN40, 1½" | ||||||||||||||
Process connection type | BA1 | ASME flange class 150, suitable for ASME B16.5, raised face (RF) | |||||||||||||
BA2 | ASME flange class 300, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
BA4 | ASME flange class 600, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA4 | ASME flange class 600, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BA5 | ASME flange class 900, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA5 | ASME flange class 900, suitable for ASME B16.5, ring joint( RJ) | ||||||||||||||
BA6 | ASME flange class 1500, suitable for ASME B16.5, raised face (RF) | ||||||||||||||
CA6 | ASME flange class 1500, suitable for ASME B16.5, ring joint (RJ) | ||||||||||||||
BD4 | EN flange PN 40, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED4 | EN flange PN 40, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD4 | EN flange PN 40, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD4 | EN flange PN 40, suitable for EN 1092-1 type D, groove | ||||||||||||||
BD6 | EN flange PN 100, suitable for EN 1092-1 type B1, raised face (RF) | ||||||||||||||
ED6 | EN flange PN 100, suitable for EN 1092-1 type E, spigot | ||||||||||||||
FD6 | EN flange PN 100, suitable for EN 1092-1 type F, recess | ||||||||||||||
GD6 | EN flange PN 100, suitable for EN 1092-1 type D, groove | ||||||||||||||
BJ1 | JIS flange 10K, JIS B 2220 | ||||||||||||||
BJ2 | JIS flange 20K, JIS B 2220 | ||||||||||||||
BP1 | JPI flange class 150 | ||||||||||||||
BP2 | JPI flange class 300 | ||||||||||||||
BP4 | JPI flange class 600 | ||||||||||||||
HS4 | Clamp process connection according to DIN 32676 series A | ||||||||||||||
HS8 | Clamp process connection according to DIN 32676 series C(Tri-Clamp) | ||||||||||||||
TG9 | Process connection with internal thread G | ||||||||||||||
TT9 | Process connection with internal thread NPT | ||||||||||||||
Sensor housing 0material | 0 | Stainless steel 1.4301/304, 1.4404/316L | |||||||||||||
1 | Stainless steel 1.4404/316L | ||||||||||||||
Process fluid temperature range | 0 | Standard: -50 to 150℃ (-58 to 302℉) | |||||||||||||
2 | Mid-range: -50 to 260℃ (-58 to 500℉) | ||||||||||||||
Mass flow and density accuracy | E7 | Liquid: 0.2 % maximum mass flow deviation, 4 g/l density deviation | |||||||||||||
D7 | Liquid: 0.15 % maximum mass flow deviation, 4 g/l density deviation | ||||||||||||||
D3 | Liquid: 0.15 % maximum mass flow deviation, 1 g/l density deviation | ||||||||||||||
C7 | Liquid: 0.1 % maximum mass flow deviation, 4 g/l density deviation | ||||||||||||||
D2 | Liquid: 0.15 % maximum mass flow deviation, 0.5 g/l density deviation | ||||||||||||||
C3 | Liquid: 0.1 % maximum mass flow deviation, 1 g/l density deviation | ||||||||||||||
C2 | Liquid: 0.1 % maximum mass flow deviation, 0.5 g/l density deviation | ||||||||||||||
70 | Gas: 0.75% maximum mass flow deviation | ||||||||||||||
50 | Gas: 0.5% maximum mass flow deviation | ||||||||||||||
Design and housing | A | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and standard neck sensor | |||||||||||||
B | Remote type with "urethane-cured polyester powder coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
E | Remote type with "corrosion protection coating" coated aluminum transmitter housing and standard neck sensor | ||||||||||||||
F | Remote type with "corrosion protection coating" coated aluminum transmitter housing and long neck sensor | ||||||||||||||
J | Remote type stainless steel transmitter and standard neck sensor | ||||||||||||||
K | Remote type stainless steel transmitter and long neck sensor | ||||||||||||||
Ex approval | NN00 | None | |||||||||||||
KF21 | ATEX, explosion group IIC and IIIC | ||||||||||||||
KF22 | ATEX, explosion group IIB and IIIC | ||||||||||||||
SF21 | IECEx, explosion group IIC and IIIC | ||||||||||||||
SF22 | IECEx, explosion group IIB and IIIC | ||||||||||||||
GF21 | EAC Ex, explosion group IIC and IIIC | ||||||||||||||
GF22 | EAC Ex, explosion group IIB and IIIC | ||||||||||||||
FF11 | FM, groups A, B, C, D, E, F, G | ||||||||||||||
FF12 | FM, groups C, D, E, F, G | ||||||||||||||
UF21 | INMETRO, explosion group IIC and IIIC | ||||||||||||||
UF22 | INMETRO, explosion group IIB and IIIC | ||||||||||||||
NF21 | NEPSI, explosion group IIC and IIIC | ||||||||||||||
NF22 | NEPSI, explosion group IIB and IIIC | ||||||||||||||
PF21 | Korea Ex, explosion group IIC and IIIC | ||||||||||||||
PF22 | Korea Ex, explosion group IIB and IIIC | ||||||||||||||
Cable entries | 2 | ANSI ½" NPT | |||||||||||||
4 | ISO M20x1.5 | ||||||||||||||
Communication type and I/O | JA | active current output HART,1 passive pulse or status output | |||||||||||||
JB | 2 active current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JC | 2 active current outputs one with HART,1 passive pulse or status output,1 voltage-free status input | ||||||||||||||
JD | 1 active current output HART,2 passive pulse or status outputs,1 passive status output | ||||||||||||||
JE | 1 active current output HART,2 passive pulse or status outputs,1 voltage-free status input | ||||||||||||||
JF | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output with pull-up resistor,1 voltage-free status input | ||||||||||||||
JG | 1 active current output HART,1 passive pulse or status output,1 active pulse or status output,1 voltage-free status input | ||||||||||||||
JH | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 active current input | ||||||||||||||
JJ | 1 active current output HART,2 passive pulse or status outputs,1 active current input | ||||||||||||||
JK | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 active current input | ||||||||||||||
JL | 1 active current output HART,1 passive pulse or status output,1 passive current output,1 passive current input | ||||||||||||||
JM | 1 active current output HART, 2 passive pulse or status outputs,1 passive current input | ||||||||||||||
JN | 1 active current output HART,1 passive pulse or status output,1 voltage-free status input,1 passive current input | ||||||||||||||
JP | 2 passive current outputs one with HART,1 passive pulse or status output | ||||||||||||||
JQ | 2 passive current outputs one with HART,2 passive pulse or status outputs | ||||||||||||||
JR | 2 passive current outputs one with HART,1 passive NAMUR pulse or status output | ||||||||||||||
JS | 2 passive current outputs one with HART,2 passive NAMUR pulse or status outputs | ||||||||||||||
M0 | Modbus output,1 passive pulse or status output | ||||||||||||||
M2 | Modbus output,1 passive pulse or status output,1 active current input | ||||||||||||||
M3 | Modbus output, 2 passive pulse or status outputs | ||||||||||||||
M4 | Modbus output,1 passive pulse or status output, 1 active pulse or status output | ||||||||||||||
M5 | Modbus output, 1 passive pulse or status output, 1 active pulse or status output with pull-up resistor | ||||||||||||||
M6 | Modbus output,1 passive pulse or status output, 1 active current output | ||||||||||||||
M7 | Modbus output, 1 passive pulse or status output, 1 passive current input | ||||||||||||||
Display | 0 | No display | |||||||||||||
1 | With display | ||||||||||||||
Optional codes | /Optional codes |
10. Location and position of installation
Address: P.O. Box 17033, Jebel Ali Free Zone - South 2 Dubai, United Arab Emirates
Tel: +971558915937
Fax: +971558915956
E-mail:
info@rostockgroup.com
technical@rostockgroup.com
commercial@rostockgroup.com
Get the latest special offers and discount information sent to your email address.
Copyright © Rostock Group Co.,Limited All Rights Reserved. Sitemap