1. General Introduction
The PM860AK01 CPU board contains the microprocessor and RAMS memory, a real-time clock, LED indicators, INIT push button, and a Compact Flash interface.
The base plate of the PM860AK01 controller has two RJ45 Ethernet ports (CN1, CN2) for connection to the Control Network, and two RJ45 serial ports (COM3, COM4). One of the serial ports (COM3) is an RS-232C port with modem control signals, whereas the other port (COM4) is isolated and used for the connection of a configuration tool.
Simple DIN rail attachment / detachment procedures, using the unique slide & lock mechanism. All base plates are provided with a unique Ethernet address which provides every CPU with a hardware identity. The address can be found on the Ethernet address label attached to the TP830 base plate.
2. Specification of PM860AK01
General info | |
Article number | 3BSE066495R1 (PM860AK01) |
Redundancy | No |
High Integrity | No |
Clock Frequency | 48MHz |
Performance, 1000 Boolean operations | 0.23 ms |
Performance | 0.23ms |
Memory | 16 MB (from 800xA 5.1 FP4) |
RAM available for application | 10.346MB(from 800xA 5.1 FP4) |
Flash memory for storage | Yes |
Detailed data | |
Processor type | MPC860 |
Switch over time in red. conf. | NA |
No. of applications per controller | 32 |
No. of programs per application | 64 |
No. of diagrams per application | 128 |
No. of tasks per controller | 32 |
Number of different cycle times | 32 |
Cycle time per application programs | Down to 1 ms |
Flash PROM for firmware storage | 2MB |
Power supply | 24 V DC (19.2-30 V DC) |
Power consumption +24 V typ/max | 180 / 300 mA |
Power dissipation typ. | 4.32 W (7.2 W max) |
Redundant power supply status input | Yes |
Built-in back-up battery | Lithium, 3.6 V |
Real-time clock stability | 100 ppm (approx. 1 h/year) |
Clock synchronization | 1 ms between AC 800M controllers by CNCP protocol |
Event queue in controller per OPC client | Up to 3000 events |
AC 800M transm. speed to OPC server | 36-86 events/sec ,113-143 data messages/sec |
Comm. modules on CEX bus | 12 |
Supply current on CEX bus | Max2.4 A |
I/O clusters on Module bus with non-red. CPU | 1 electrica+7 optical |
I/O clusters on Module bus with red. CPU | NA |
I/O capacity on Module bus | Max 96 I/O modules |
Module bus scan rate | 0 - 100 ms (actual time depending on number of I/O modules) |
Supply current on Electrical Module bus | 24 V : max 1.0 A 5 V : max 1.5 A |
Ethernet channels | 2 |
Ethernet interface | Ethernet (IEEE 802.3), 10 Mbit/s, RJ-45, female (8-pole) |
Control Network protocol | MMS (Manufacturing Message Service) and IAC (Inter Application Communication) |
Recommended Control Network backbone | 100 Mbit/s switched Ethernet |
RS-232C interface | 2 (one general, 1 for service tool) |
RS-232C interface (COM3) (non red. only) | RS-232C, 75-19 200 baud, RJ-45 female (8-pole), not opto isolated, full RTSCTS support |
RS-232C interface (COM4) (non red. only) | RS-232C, 9 600 baud, RJ-45 female (8-pole), opto isolated, no RTS-CTS support |
Environmental and certification | |
Temperature, Operating | +5 to +55 °C (+41 to +131 °F) |
Temperature, Storage | -40 to +70 °C (-40 to +158 °F) |
Temperature changes | 3 °C/minutes according to IEC/EN 61131-2 |
Altitude | 2000 m according to IEC/EN 61131-2 |
Pollution degree | Degree 2 according to IEC/EN 61131-2 |
Corrosion protection | G3 compliant to ISA 71.04 |
Relative humidity | 5 to 95 %, non-condensing |
Emitted noise | < 55 dB (A) |
Vibration | 10 < f < 50 Hz: 0.0375 mm amplitude, 50 < f < 150 Hz: 0.5 g acceleration, 5 < f < 500 Hz: 0.2 g acceleration |
Rated Isolation Voltage | 500 V a.c. |
Dielectric test voltage | 50 V |
Protection class | IP20 according to EN 60529, IEC 529 |
Emission & Immunity | EN 61000-6-4, EN 61000-6-2 |
Environmental conditions | Industrial |
CE- marking | Yes |
Electrical Safety | EN 50178, IEC 61131-2, UL 508 |
Hazardous location | cULus Class 1, Zone 2, AEx nA IIC T4, ExnA IIC T4Gc X |
Marine certificates | ABS, BV, DNV-GL, LR, RS |
TUV Approval | No |
RoHS compliance | EN 50581:2012 |
WEEE compliance | DIRECTIVE/2012/19/EU |
Dimensions | |
Width | 119 mm (4.7 in.) |
Height | 186 mm (7.3 in.) |
Depth | 135 mm (5.3 in.) |
Weight | 1100 g (2.4 lbs) |
3. Selection table of controllers
Name | High Integrity | Memory | Performance | Redundancy |
BC810K02 | Yes | - | Hot swap supported | Yes |
BC820K02 | No | - | Hot swap supported | Yes |
PM851AK01 | No | 12 MB (from 800xA 5.1 FP4) | 0.46ms | No |
PM856AK01 | No | 16 MB (from 800xA 5.1 FP4) | 0.46ms | No |
PM857K01 | Yes | 16 MB | 0.17ms | No |
PM857K02 | Yes | 16 MB | 0.17ms | Yes |
PM858K01 | No | 16 MB | 0.36ms | No |
PM858K02 | No | 16 MB | 0.36ms | Yes |
PM860AK01 | No | 16 MB (from 800xA 5.1 FP4) | 0.23ms | No |
PM861AK01 Classic | No | 16 MB | 0.23ms | Yes |
PM861AK02 Classic | No | 16 MB | 0.23ms | Yes |
PM862K01 | No | 32MB | 0.18ms | No |
PM862K02 | No | 32MB | 0.18ms | Yes |
PM863K01 | Yes | 32MB | 0.17ms | No |
PM863K02 | Yes | 32MB | 0.17ms | Yes |
PM864AK01 Classic | No | 32MB | 0.15ms | Yes |
PM864AK02 Classic | No | 32MB | 0.15ms | Yes |
PM865K01 | Yes | 32MB | 0.17ms | No |
PM865K02 | Yes | 32MB | 0.17ms | Yes |
SM811 (for PM865) | Yes | 32MB | - | Yes |
PM866AK01 | No | 64 MB | 0.09 ms | No |
PM866AK02 | No | 64 MB | 0.09 ms | Yes |
PM867K01 | Yes | 64 MB | 0.09 ms | No |
PM867K02 | Yes | 64 MB | 0.09 ms | Yes |
SM(for PM867) | Yes | 64 MB | - | Yes |
PM891K01 | No | 256MB | 0.043ms | No |
PM891K02 | No | 256MB | 0.043ms | Yes |
